XTREME
Classic Klearkote 4.2 VOC
#5155 X-TREME Classic Klearkote is a medium solids clearcoatthat is easy to spray providing excellent flowout, gloss, and DOI. With three activators to choose from it offers versatility in most shop conditions and temperatures. 5155 can be used for partial or complete paint jobs in need of a high quality, durable finish.
PRODUCT DESCRIPTION:
5155 is a two component polyurethane clearcoat formulated to offer refinishers ease of application,
great flow and leveling, superior gloss and excellent distinctness of image in a 4.2 VOC conventional solid
polyurethane clearcoat.
| PRODUCTS: |
|
Gallon |
Quart |
Half Pint |
| •Classic Klearkote 4.2 VOC |
#5155-1 |
#5155-4 |
|
•Universal Urethane Activator
Fast (Spot/Panel Repairs) |
|
#5162-4 |
#5162-16 |
•Universal Urethane Activator
Medium (Multi Panel/Small
Overall) |
|
#5163-4 |
#5163-16 |
•Universal Urethane Activator
Slow (Small Overall/Larger
Overall) |
|
#5164-4 |
#5164-16 |
| •Urethane Reducer Fast |
#5650-1 |
|
|
| •Urethane Reducer Medium |
#5655-1 |
|
|
| •Urethane Reducer Slow |
#5660-1 |
|
|
| CAUTION: ACCELERATOR NOT RECOMMENDED WHEN USING #5162 FAST ACTIVATOR |
|
SURFACE PREPARATION:
• Apply Undercoats and Basecoat per manufacturer’s instruction.Over OEM or completely cured previously painted substrates scuff with a grey scuff pad or 600 grit then wipe clean with an approved solvent or water-borne wipe.
• Allow basecoat adequate flash time (follow manufacturer’s recommendation)
• Follow basecoat manufacturer’s recommendation for recoat intervals.
MIXING DIRECTIONS:
Mix 4 parts 5155 base with 1 part 5162, 5163, or 5164 by volume. Activator selection should be based on the size of the part to be painted and the temperature of both the air and part at time of painting.
APPLICATION:
| Number of Coats: |
3-4 |
| Application Density |
Medium-wet to wet |
| Overlap |
50% |
| Flash: |
Follow recommendations in "Dry Time" section |
| Film Thickness Range: |
|
| |
| Dry |
1 mil – 6 mils |
| Wet |
3 mils – 6 mils |
|
| Application Conditions |
|
|
| Minimum Temp |
50°F (Substrate Temp.) |
| Max Temp |
100°F (Substrate Temp.) |
| Ambient Humidity |
Less than 80% preferred |
|
POT LIFE:
When properly covered at 77°F, 5155 will maintain a sprayable viscosity for at least from 4-6 hours depending on activator selection.
ADDITIVES:
ACCELERATOR: N/A
FISHEYE: N/A
FLEX ADDITIVE: Not required
Note: Do not spray when surface temperature is below 50°F.
CLEAN UP AND STORAGE:
Clean spray equipment immediately after use with gun wash solvent.
SUBSTRATES:
• Commercially available acrylic/cab basecoats with a VOC less than 6.6 lbs/gal
• Properly prepared previously painted substrates
GUN SETUPS:
| CONVENTIONAL |
|
| Gravity Feed |
1.3 mm – 1.5 mm tip |
| Siphon Feed |
1.6 mm – 1.8 mm tip |
| HVLP |
1.3 mm – 1.6 mm |
| AIR PRESSURES |
|
|
| Conventional @ Gun |
PANEL |
OVERALL |
| Gravity Feed |
35-40 psi |
45 psi |
| Siphon Feed |
35-45 psi |
45-50 psi |
| HVLP @ Cap |
6-8 psi |
9-10 psi |
FLASH/DRY TIMES:
| |
5162 @ or
above 77°F |
5163 @ or
above 85°F |
5164 @ or
above 95°F |
|
| Flash Between Coats |
| 5-10 min |
5-10 min |
5-10 min |
|
| Dust Free |
| 10-15 min |
10-15 min |
10-15 min |
|
| Sand/Polish |
| 4-6 hours |
4-6 hours |
4-6 hours |
|
| |
|
| Force Dry (Convection Heat) |
|
| |
|
| Purge time before applying heat |
|
| Force Dry Time |
| 20 min @ 165°F |
20 min @ 165°F |
20 min @ 165°F |
|
| Sand and Buff |
| After Cool Down |
After Cool Down |
After Cool Down |
|
TECHNICAL DATA:
| Density |
7.64 lbs/gal (unactivated) |
| Solids |
|
By Weight
By Volume |
36.2%
29.0% |
| VOC (Volatile Organic Content) |
3.67 lbs/gal |
| Viscosity |
17" Zahn #2 |
| Flash Point |
-4°F |
| Theoretical Coverage |
465 F2/gal @ 1 mil thickness |
SAFETY INFORMATION FOR INDUSTRY USE ONLY:
Danger: Vapor and spray mist harmful. Overspray may cause lung damage. May cause allergic skin and respiratory reaction, effects may be permanent. Flammable liquid and vapor. Harmful if inhaled. May affect the brain or nervous system causing dizziness, headache, or nausea. Maycause eye, skin, nose, and throat irritation.
Contents: See product label for contents and CAS #’s. The contents of this package must be blended with other components before the product can be used. Any mixture of components will have hazards of all components. Before opening the packages, read all warning labels. Follow all precautions. The material is designed for application only by professionally trained personnel using proper equipment under controlled conditions, and is not intended for sale to the general public. KEEP OUT OF REACH OF CHILDREN. ABI® Autobody Brands International Scottsdale, AZ - www.autobodybrands.com
Call 1-87REFINISH (1-877-334-6474) to
find your local 5 Star Autobody Products
supplier. Or visit our website:
www.autobodybrands.com
Top
|
