XTREME
“Flat Finish” Klearkote 4.4 VOC
PRODUCT DESCRIPTION:
#5165 XTREME “FLAT FINISH” KLEAR is a matte finish clearcoat designed to offer that very popular Old School, no gloss look when used over any color basecoat paint, while offering the UV protection
and durability of a standard clearcoat finish.
| PRODUCTS: |
| |
Gallon/cs |
Quart/cs |
| XTREME Original Flat Finish Klearkote 4.4 VOC |
#5165-1 |
#5165-4 |
| XTREME Original Flat Finish Activator 4.4 VOC |
|
#5187-4 |
|
BASECOAT:
Apply basecoat as per manufacturer’s mixing and application instructions. Allow
sufficient flash times before applying #5165. Inadequate flash time will affect the
performance of the clear.
MIXING RATIO (6:1):
Mix 6 parts #5165 FLAT FINISH Klearkote to 1 part #5187 Activator.
APPLICATION:
Apply 2 even coats at 40-50 psi or (6-10 psi when using HVLP at the gun),
allowing a 10-15 minute flash between coats.
NOTE:Wet coats will produce more gloss.Drier coats will produce a flat finish. Uneven coating can produce varied gloss levels in the finish.
| DRY TIMES AT 77° F: |
| Dust Free |
10 - 15 minutes |
| Tack Free |
45 minutes |
| To Deliver |
16 - 24 hours |
| |
|
| FORCE DRYING: |
| Flash Time @ 77° F |
15 minutes |
| Bake Time @ 140° F |
30 minutes |
| Allow a one to two hour cool-down time before wet sanding or buffing
after force drying. |
RECOATING:
#5165 may be recoated after a 24 Hour dry at 77° F, or upon cool down after force
drying at 140° F for 30 minutes.
POT LIFE:
Pot life will be about 4-5 hours at 77°F.
CLEAN-UP:
Clean equipment immediately using 5 STAR #5700 Premium Lacquer Thinner or
#5685 Urethane Reducer.
TECHNICAL DATA:
| Mixing Ratio: |
6 parts #5165: 1 part #5187 |
| Viscosity (RTS): |
17-19 seconds #2 Zahn |
| Volume Solids (RTS): |
28% |
| Film Build: |
0.8 - 1.0 mils per full wet coat |
| Coverage: |
449 sq. ft. per gallon @ 1 dry mil |
| Disposal/Safety: |
see MSDS for this product |
| Humidity Resistance: |
Excellent |
| Salt Spray Resistance: |
Excellent |
FIRST AID:
In case of eye contact, immediately flush eyes with plenty of water for at least 15
minutes and get medical attention. For skin: Wash thoroughly with water. If
difficulty in breathing is experienced, get medical attention immediately. If
swallowed, do not induce vomiting, get medical attention immediately. See Material Safety Data Sheet.
SAFETY INFORMATION FOR INDUSTRY USE ONLY:
Danger: Vapor harmful.May affect the brain or nervous system causing dizziness, headache, or nausea. May cause eye, skin, nose,
and throat irritation. Harmful if swallowed. Precautions: Vapors may ignite explosively. Keep away from heat, sparks, and flame.
Vapors may cause flash fire.Do not smoke. Extinguish all flames and pilot lights, and turn of stoves, heaters, electric motors and
other sources of ignition during use and until all vapors are gone. Prevent buildup of vapors by opening all windows and doors to
achieve cross-ventilation. Use only with adequate ventilation. Do not breathe vapor or spray mist.Do not get in eyes, on skin or
clothing.Wash thoroughly after handling.Wear solvent resistant gloves. The material id designed for application only by
professionally trained personnel using proper equipment under controlled conditions, and is not intended for sale to the general
public. KEEP OUT OF REACH OF CHILDREN. ABI - AutobodyBrands International a division of IAMG - International Autobody
Marketing Group - Scottsdale, AZ - www.autobodybrands.com
Call 1-87REFINISH (1-877-334-6474) to
find your local 5 Star Autobody Products
supplier. Or visit our website:
www.autobodybrands.com
Top
|
|
