XTREME
Original Speed Klearkote 2.1 VOC
PRODUCT DESCRIPTION:
#5173 XTREME Speed Klearkote is a high-gloss, two component
Urethane Clear designed for speed! Its fast setting and through
cure, offer an excellent combination of outstanding appearance
and performance! 2.1 VOC Compliant.
| PRODUCTS: |
| |
Gallon/cs |
Quart/cs |
Half Pint/cs |
| Original Speed Klearkote 2.1 VOC |
#5173-1 |
#5173-4 |
|
| Original Activator Fast |
|
#5181-4 |
#5181-16 |
| Original Activator Medium |
|
#5182-4 |
#5182-16 |
| Original Activator Slow |
|
#5183-4 |
#5183-16 |
|
SURFACE PREPARATION:
Apply Undercoats and Basecoat per manufacturer’s instruction. Over OEM
or completely cured previously painted substrates scuff with a grey scuff
pad or 600 grit then wipe clean with an approved solvent or water-borne wipe. Allow basecoat adequate flash time
(follow manufacturer’s recommendation). Follow basecoat manufacturer’s recommendation for recoat intervals.
MIXING DIRECTIONS:
Mix 4 parts 5173 base with 1 part 5181, 5182, or 5183 by volume. Activator
selection should be based on the size of the part to be painted and the
temperature of both the air and part at time of painting.
| APPLICATION: |
| Number of Coats: |
2-3 |
| Application Density: |
Medium-wet to wet |
| Overlap: |
50% |
| Flash: |
Follow recommendations in "Dry Time" section |
| |
|
| Film Thickness Range: |
|
| Dry |
1 mil – 4 mils |
| Wet |
3 mil – 4 mils |
| |
|
| Application Conditions: |
|
| Minimum Temp |
50°F (Substrate Temp.) |
| Max Temp |
100°F (Substrate Temp.) |
| Ambient Humidity |
Less than 80% preferred |
POT LIFE:
When properly covered at 77°F,
5173 will maintain a sprayable
viscosity for at least from 1-3 hours depending on activator
selection.
| ADDITIVES: |
| ACCELERATOR: N/A |
FISHEYE: N/A |
FLEX ADDITIVE: Not required |
| Note: Do not spray when surface temperature is below 50°F |
CLEAN UP:
Clean spray equipment immediately after use with gun wash solvent.
SUBSTRATES:
Commercially available basecoats with a VOC less than 6.6 lbs/gal
Properly prepared previously painted substrates.
| GUN SETUPS: |
| CONVENTIONAL |
|
|
| Gravity Feed |
1.3 mm – 1.5 mm |
|
| Siphon Feed |
1.6 mm – 1.8 mm |
|
| HVLP |
1.3 mm – 1.5 mm |
|
| |
|
|
| AIR PRESSURES |
|
|
| Conventional @ Gun |
PANEL |
OVERALL |
| Gravity Feed |
35-40 psi |
45 psi |
| Siphon Feed |
35-45 psi |
45-50 psi |
| HVLP @ Cap |
6-8 psi |
9-10 psi |
| FLASH/DRY TIMES: |
| |
5186 @ or
above 77°F |
5187 @ or
above 85°F |
5188 @ or
above 95°F |
| Flash Between Coats |
5-10 min |
5-10 min |
5-10 min |
| Dust Free |
10-15 min |
10-15 min |
10-15 min |
| Sand/Polish |
1.5-2 hours |
1.5-2 hours |
1.5-2 hours |
| |
|
|
|
| Force Dry (Convection Heat) |
| |
5186 |
5187 |
5188 |
| Purge time before applying heat |
0-15 min |
0-15 min |
0-15 min |
| Force Dry Time |
20 min @ 165°F |
20 min @ 165°F |
20 min @ 165°F |
| Sand and Buff |
After Cool Down |
After Cool Down |
After Cool Down |
| |
|
|
|
TECHNICAL DATA:
| VOC (Volatile Organic Content): |
2.1 lbs/gal |
| Viscosity: |
17-19 seconds Zahn #2 |
| Flash Point: |
-4°F |
| Film Build: |
1.0 mils per full wet coat |
| Theoretical Coverage: |
531 ft2/gal @ 1 mil thickness |
| Solids (Ready to Spray): |
|
|
SAFETY INFORMATION FOR INDUSTRY USE ONLY:
Danger: Vapor and spray mist harmful.Overspray may cause lung damage.May cause allergic skin and respiratory reaction, effects may be permanent.
Flammable liquid and vapor.Harmful if inhaled. May affect the brain or nervous system causing dizziness, headache, or nausea. May cause eye, skin, nose,
and throat irritation.Contents: See product label for contents and CAS #’s. The contents of this package must be blended with other components
before the product can be used. Any mixture of components will have hazards of all components. Before opening the packages, read all warning
labels. Follow all precautions. The material id designed for application only by professionally trained personnel using proper equipment under
controlled conditions, and is not intended for sale to the general public. KEEP OUT OF REACH OF CHILDREN
ABI/ Autobody Brands International a division of I.A.M.G. - Scottsdale,AZ - www.autobodybrands.com
Call 1-87REFINISH (1-877-334-6474) to
find your local 5 Star Autobody Products
supplier. Or visit our website:
www.autobodybrands.com
Top
|
|
