XTREME
Original Klearkote 4.4 VOC

Enlarge Image

#5185      #5187 #5186      #5188

This new ALL Temperature Urethane clear is very easy to use and provides great gloss and DOI. Its three Activators allow it to be used in most temperatures and make it versatile enough to be used as a Spot or Multi-Panel Clear. With its 4:1 Mix Ratio, it is truly the best new clear around!

PRODUCT DESCRIPTION:
#5185 is a urethane clearcoat with a sprayable VOC of 4.4 lbs/gal. It is a fast drying user friendly clearcoat that produces an extremely durable finish.

FEATURES:
• VOC: 4.4 lbs/gal
• 4:1 Mix Ratio
• Easy Buff
• 3 Activators (3 temperature ranges)
• High Gloss

SURFACE PREPARATION:
Surface must be clean, dry, and free of any contaminants, such as wax, oil, etc...
1. Always wash vehicle with soap and water.
2. Wipe surface with 5 Star Autobody Products Wax & Grease Remover or #5905 Surface Prep.
3. Abrade the surface to remove any corrosion.
4. Re-clean area with #5905 Surface Prep.
5. Prime bare metal with appropriate primers.

BASECOAT:
Apply basecoat per manufacturer's mixing and application instructions. Allow sufficient flash time before applying clear. Please note that basecoat flash times could vary between basecoats. Inadequate flash times will affect the performance of this product.

MIXING DIRECTIONS:
4 parts of X-TREME KlearKote to 1 part X-TREME Activator.

APPLICATION:
1. Adjust air pressure to 45-50 psi (Siphon); 35-40 (Gravity); 6-10 (HVLP).
2. Apply 2-3 flowing coats.
3. Allow 10-15 minutes flash time between coats. Keep spray gun 6-10 inches from substrate to avoid problems associated with air entrapment.
4. Allow to dry overnight before exposing to the weather.

BLENDING PROCEDURES:
1. Before blending a panel with clear, the blend area must be compounded and cleaned thoroughly with a quality pre-paint cleaner. Do not leave compound residue on surface.
2. Apply wet coat of clear over painted area and slightly beyond. Allow 5-10 minutes flash.
3. Apply second wet coat of clear 4-6 inches beyond first coat. Allow 5-10 minute flash.
4. Reverse blend the third coat by starting 3-5 inches beyond the dry edge and spray into the center of the painted area. Additional reduction with a urethane reducer may be desired to melt in overspray.

FORCE DRY:
Air Dry for 30 minutes, then force dry for 30 minutes at 140 degrees F. Clear may be wet sanded after one hour.

POT LIFE:
Pot Life with #5186 will be about 4-5 hours at 77 degrees F. WHen using #5187 or #5188 the pot life will be 8-10 hours.

SANDING:
Final sand with 1200 or finer grit paper after 16-24 hours or upon cool down after force drying.

BUFFING:
Buff with appropriate compound after 6-8 hours.

ACCELERATOR:
To improve the Buff & Sanding time, or for faster dry and cure times in colder conditions, add 2 to 4 ounces of #5405 Urethane Accelerator to a gallon of catalyzed clear.  Please note that the accelerator will shorten the pot life and slightly reduce the gloss. Do not use #5405 Urethane Accelerator when using #5186.

CLEAN UP AND STORAGE:
Clean equipment immediately using 5 Star #5700 or #5703 Lacquer Thinner or #5650 Urethane Reducer.

NOTE: Some spray gun manufacturers have specific recommendation for specific spray guns & product viscosity, always check spray gun manufacturers recommendation:

SAFETY INFORMATION FOR INDUSTRY USE ONLY:
Danger: Vapor and spray mist harmful. Overspray may cause lung damage.  May cause allergic skin and respiratory reaction, effects may be permanent. Flammable liquid and vapor. Harmful if inhaled. May affect the brain or nervous system causing dizziness, headache, or nausea. May cause eye, skin, nose, and throat irritation. Contents: See product label for contents and CAS #'s. The contents of this package must be blended with other components before the product can be used.  Any mixture of components will have hazards of all components.  Before opening the packages, read all warning labels.  Follow all precautions.  The material is designed for application only by professional trained personnel using proper equipment under controlled conditions, and is not intended for sale to the general public.  KEEP OUT OF REACH OF CHILDREN. ABI® Autobody Brands International Scottsdale, AZ - www.autobodybrands.com

Call 1-87REFINISH (1-877-334-6474) to
find your local 5 Star Autobody Products
supplier. Or visit our website:
www.autobodybrands.com

Top