MAXX FILL 2K
2.1 VOC High Build Urethane Primer Surfacer – Gray
5452 is formulated to provide a fast-drying,
high-build film that has maximum adhesion,
easy sanding properties and excellent color
holdout. 5452 is designed to be used on
properly prepared steel, aluminum, iron,
fiberglass and previously painted surfaces.
This primer surfacer can be topcoated with
any paint system. Offered in a Gray color.
PRODUCT DESCRIPTION:
5452 is formulated to provide a fast-drying, high-build film that has maximum adhesion, easy sanding
properties & excellent color holdout. 5452 is designed to be used on properly prepared steel, aluminum, iron,
fiberglass & previously painted surfaces. This primer surfacer can be topcoated with any paint system and is also tintable.
FEATURES:
• 2.1 VOC
• 4:1:1 Mix Ratio
• Tintable
• Excellent Adhesion
Characteristics
• Hi-Build, Superior Holdout
• Fast Drying
• Easy Sanding Properties
• Can Be Topcoated With Any
Automotive Paint System
| PRODUCTS: |
| |
Gallon |
Quart |
Half Pint |
| 2.1 VOC Primer (Gray) |
#5452-1 |
#5452-4 |
|
| 2.1 VOC Activator |
|
#5458-4 |
#5458-16 |
|
SURFACE PREPARATION:
Clean all areas to be painted with compliant Wax & Grease Remover to remove all dirt,wax, grease and other contaminants.
Featheredge and sand original finish. Surface must be clean and dry. For maximum adhesion to bare galvanized steel and
aluminum, coat with 5 STAR #5414 & #5415 Self Etching Primer prior to applying #5452 MAXX FILL 2K High Build Primer.
| MIXING DIRECTIONS: |
| Mix the components in the order and ratio indicated below. Stir thoroughly after adding each item. |
| |
•
•
• |
4 PARTS #5452 2.1 VOC MAXX FILL Gray Primer
1 PART #5458 2.1 VOC MAXX FILL Activator
1 Part 5 STAR Urethane Grade Reducer (available in fast, med, & slow) |
|
| |
| Tinting Directions |
|
5% tint paste or toner from any urethane compatible paint system.Tinting primer may affect sanding
and dry times. |
|
APPLICATION & DRY TIME DIRECTIONS:
Apply 2 full wet coats at 40-50 psi to achieve 3 mils of film that can
be sanded and topcoated in 1 to 2 hours.
POT LIFE:
Approximately 2 hours.
COMPATIBLE BASECOATS :
BASF, Dupont, ICI, PPG, Sherwin Williams, Sikkens, Spies Hecker, Valspar
| GUN SETUP: |
| GUN SET-UP: CONVENTIONAL |
| CONVENTIONAL |
1.5 mm - 2.2 mm |
| HVLP |
1.5 mm - 2.2 mm |
| |
| AIR PRESSURE |
| CONVENTIONAL @ GUN |
35-45 psi |
| HVLP @ GUN |
28-35 psi |
FLASH/DRY TIMES:
Let each coat flash 5-10 minutes. Better appearance and color holdout will be achieved by letting dry 6-8 hours prior to
sanding and topcoating. It can be force dried for 30 minutes at 140°F (60°C) after allowing the final coat to flash 10 minutes.
Films in excess of 3 mils should not be force dried. If 6-8 mils film build is desired, omit the 5 STAR Urethane Grade Reducer & use a gravity feed gun at 30-35 psi at the gun. Allow 15 minutes flash between coats. Films in excess of 3 mils must be dried
overnight before sanding and topcoating. Pot life will be approximately one hour. 5452 must always be sanded before topcoating.
CLEAN UP:
Clean spray equipment immediately after use with 5 STAR #5414 Virgin Wash Thinner or Urethane Grade
Reducer. Do not leave material in spray gun.
VOC REGULATIONS:
2.1 Mixed VOC.This product meets the VOC stipulated by the SCAQMD Rule 1151 and the
USEPA National Rule. Check local government VOC rules for comp
FIRST AID:
In case of eye contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical
attention. For skin: Wash thoroughly with water. If difficulty in breathing is experienced, get medical attention
immediately. If swallowed, do not induce vomiting, get medical attention immediately. See Material Safety
Data Sheet.
SAFETY INFORMATION – FOR INDUSTRY USE ONLY:
Danger: Vapor harmful.May affect the brain or nervous system causing dizziness, headache, or nausea. May cause eye, skin, nose, and throat irritation. Harmful
if swallowed. Precautions: Vapors may ignite explosively. Keep away from heat, sparks, and flame. Vapors may cause flash fire.Do not smoke. Extinguish all flames
and pilot lights, and turn of stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Prevent buildup of vapors by
opening all windows and doors to achieve cross-ventilation. Use only with adequate ventilation. Do not breathe vapor or spray mist.Do not get in eyes, on
skin or clothing.Wash thoroughly after handling. Wear solvent resistant gloves. The material id designed for application only by professionally trained personnel
using proper equipment under controlled conditions, and is not intended for sale to the general public. KEEP OUT OF REACH OF CHILDREN. ABI® Autobody
Brands International Scottsdale, AZ - www.autobodybrands.com
Call 1-87REFINISH (1-877-334-6474) to
find your local 5 Star Autobody Products
supplier. Or visit our website:
www.autobodybrands.com
Top
|
|
