MAXX FILL 2K
High Build Urethane Primer Surfacer — Buff 4.4 VOC

Enlarge Image

5453 5457

Designed for repairs of any size, MAXX FILL 2K is the perfect combination of performance and versatility!

PRODUCT DESCRIPTION:
5453 is formulated to provide a fast-drying, high-build film that has excellent adhesion, easy sanding properties and excellent color holdout. It is designed to be used on properly prepared steel, aluminum, iron, fiberglass and previously painted surfaces.This primer surfacer can be topcoated with any paint system. Offered in a Buff (Yellow) color.

COLOR:
Buff (Yellow) color.

SURFACE PREPARATION:
Clean all areas to be painted with 5 STAR #5901 Wax & Grease Remover to remove all dirt,wax, grease and other contaminants. Featheredge and sand original finish. Surface must be clean and dry. Bare galvanized steel and aluminum should be coated with 5 STAR #5414 and #5415 Self-Etch Primer prior to applying #5453 MAXX FILL 2K Urethane Primer Surfacer.

APPLICATION & DRY TIME DIRECTIONS:
Apply 2 full wet coats at 40-50 psi to achieve 3 mils of film that can be sanded and topcoated in 3 hours. Sanding and cure time may be longer depending on thickness of application, tints used and/or temperature. Let each coat flash 5-10 minutes. Better appearance and holdout will be achieved by letting dry 6-8 hours prior to sanding and topcoating. It can also be force-dried for 30 minutes at 140°F (60°C) after allowing the final coat to flash 20 minutes. Films in excess of 3 mils should not be force-dried. #5453 MAXX FILL 2K Urethane Primer Surfacer must always be sanded before topcoating.

POT LIFE:
Mix the components in the order and ratio of: 4 parts #5453 primer with 1 part #5457 activator, and 1 part 5 STAR Urethane Grade Reducer. Stir thoroughly after adding each item. Pot life of activated primer is approximately 2 hours.

COMPATIBLE BASECOATS :
BASF, Dupont, ICI, PPG, Sherwin Williams, Sikkens, Spies Hecker, Valspar.

CLEAN UP:
Clean spray equipment immediately after use with 5 STAR #5214 Virgin Wash Thinner or Urethane Grade Reducer.Do not leave material in spray gun.

FIRST AID:
In case of eye contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical attention: for skin,wash thoroughly with soap and water. If difficulty in breathing is experienced, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately. If swallowed, do not induce vomiting.Get medical attention immediately. See Material Safety Data Sheet.

SAFETY INFORMATION – FOR INDUSTRY USE ONLY:
Danger: Vapor harmful.May affect the brain or nervous system causing dizziness, headache, or nausea. May cause eye, skin, nose, and throat irritation. Harmful if swallowed. Precautions: Vapors may ignite explosively. Keep away from heat, sparks, and flame. Vapors may cause flash fire. Do not smoke. Extinguish all flames and pilot lights, and turn of stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Prevent buildup of vapors by opening all windows and doors to achieve cross-ventilation. Use only with adequate ventilation. Do not breathe vapor or spray mist. Do not get in eyes, on skin or clothing.Wash thoroughly after handling.Wear solvent resistant gloves.The material id designed for application only by professionally trained personnel using proper equipment under controlled conditions, and is not intended for sale to the general public. KEEP OUT OF REACH OF CHILDREN. ABI® Autobody Brands International Scottsdale, AZ - www.autobodybrands.com

Call 1-87REFINISH (1-877-334-6474) to
find your local 5 Star Autobody Products
supplier. Or visit our website:
www.autobodybrands.com

Top