FRAME BLACK
GLOSS BLACK CHASSIS PAINT
NOT SCAQMD 102 & 1151 Rule Compliant
5410 is an economical protective coating for
chassis, engine compartments, and miscellaneous
parts to refinish. It has excellent adhesion and
impact resistance. 5410 is resistant to fuels
when thoroughly cured using 5 STAR #5132
Enamel Hardener. Offered in gloss black.
PRODUCT DESCRIPTION:
5410 Frame Black is an economical protective coating for chassis, engine compartments, and miscellaneous parts to refinish.
It has excellent adhesion and impact resistance. 5410 is resistant to fuels when thoroughly cured using 5 STAR #5132 Enamel
Hardener. Offered in Gloss Black. NOT SCAQMD 102 & 1151 Rule Compliant.
| FEATURES: |
| |
• 4.6 VOC
• Ready to Spray!
• Gloss Black
• Excellent Adhesion
Characteristics
• Superior Impact Resistance
• Fast Drying |
| PRODUCTS & COLOR: |
| |
Gallon/cs |
Quarts/cs |
Pint/cs |
4.6 VOC Frame Black
(Gloss Black Paint
for Chassis) |
#5410-1 |
#5410-4 |
|
| If Desired:
Synthetic Enamel Hardener |
|
|
#5132-8 |
|
SURFACE PREPARATION:
Prior to repair,wash the surface with mild detergent and hot water,making sure to rinse well and dry with a clean dry cloth.
Solvent clean with 5 STAR #5902 FinalWipeWax & Grease Remover to remove any contaminants prior to sanding or bodywork. Final
sand bare metal with 150 – 220 grit sandpaper. Final sand painted surfaces with 220-320 grit sandpaper. Final clean with 5 STAR
#5902,making sure surface is clean and dry. Final wipe using a tack cloth.
| MIXING DIRECTIONS: READY TO SPRAY. NO MIXING REQUIRED |
OPTIONAL MIX BY VOLUME - For Added Durability & Protection
Mix the components in the order and ratio indicated below.
Stir thoroughly after adding each item.
|
|
| #5410 FRAME BLACK Paint |
8 Parts |
| #5132 Enamel Hardener |
1 Parts |
| MIX RATIO IN OUNCES |
| COLOR |
8 |
16 |
24 |
32 |
48 |
64 |
| HARDENER |
1 |
2 |
3 |
4 |
6 |
8 |
|
APPLICATION & DRY TIME DIRECTIONS:
Allow appropriate dry times for primers and sealers. Strain paint prior to application. Apply one medium-wet coat and allow 10 minutes flash or until surface is hand slick. Apply a second full wet coat. For best results, do not apply more than 2 coats.
| BAKING - 5410 MUST BE HARDENED IN ORDER TO BAKE OR FORCE DRY |
| Full Bake Cycle: |
Allow 30 minutes purge. Bake 30 minutes - 1 hour at 140°F. Allow a 2 hour cool down prior to assembling. |
|
POT LIFE:
4 – 6 hours at 75°F (if hardened with 5132). Do not try to thin color after thickening has occurred – do not
use. Clean equipment immediately after use. Note: Accelerators, reducers, and temperature will affect pot life.
COMPATIBLE SUBSTRATES:
Bare Steele.
| GUN SETUP: |
Fluid Tip |
Air Pressure |
| HVLP Gravity |
1.3mm - 1.4mm |
6 - 10 PSI at the cap |
| HVLP Siphon |
1.5mm - 1.8mm |
6 - 10 PSI at the cap |
| Con.Gravity |
1.3mm - 1.4mm |
50 PSI at the gun |
| Con. Siphon |
1.5mm - 1.8mm |
50 PSI at the gun |
| DATA: |
|
|
Dust Free - 20 minutes
(will vary with hardener & reducer) |
Solvent Resistance - Xylene pass 100 rubs
(w/ 5132) |
| Dry to Handle - 2 hours |
Recommended Coats - 2 |
| VOC as applied - 4.6 lbs/gal |
DFT per coat +/- .20 mils |
| Mixed Volume Solids - 36.62% |
Theoretical Coverage - 587 sq. ft @ 1 mil.DFT |
Film Hardness - 2H
(w/ 5132 Hardener) |
|
NOTES:
Use in shop temperatures that are maintained above 75°F for the first 24-hours of the cure cycle. Ensure surfaces are up to shop temperature prior to work. Ensure proper metal conditioning/preparation procedures in early stages are followed.Use a mixing cup for accurate volume measurements. 5410 will be water resistant in 24-hours. Note: Do not allow raindrops to dry on a new finish for the first 3 – 4 days to prevent staining.
CLEAN UP:
Clean spray equipment immediately after use with Urethane Grade Reducer or 5 STAR #5414 VirginWash
Thinner. Do not leave material in spray gun.
DISPOSAL:
Dispose of all paint and paint related materials in accordance with state and local regulations.
SAFETY INFORMATION – FOR INDUSTRY USE ONLY:
Danger: Vapor harmful.May affect the brain or nervous system causing dizziness, headache, or nausea. May cause eye, skin, nose, and throat irritation. Harmful if swallowed. Precautions: Vapors may ignite explosively. Keep away from heat, sparks, and flame. Vapors may cause flash fire. Do not smoke. Extinguish all flames and pilot lights, and turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Prevent buildup of vapors by opening all windows and doors to achieve cross-ventilation. Use only with adequate ventilation. Do not breathe vapor or spray mist. Do not get in eyes, on skin or clothing. Wash thoroughly after handling. Wear solvent resistant gloves. The material is designed for application only by professionally trained personnel using proper equipment under controlled conditions, and is not intended for sale to the general public. KEEP OUT OF REACH OF CHILDREN. ABI - Autobody Brands International a division of IAMG - International Autobody Marketing Group. Scottsdale, AZ - www.autobodybrands.com
Call 1-87REFINISH (1-877-334-6474) to
find your local 5 Star Autobody Products
supplier. Or visit our website:
www.autobodybrands.com
Top
|
|
